> Dispensers > Manual > Derfi’s production safe cut > DC Sleeve

DC Sleeve

Manual dispenser for adhesive tape Sleeve type with pressure-sensitive cutter system

This manual dispenser has been specifically designed to facilitate the cutting of Sleeve adhesive tapes. Sleeve is a very specific material that is unfortunately often difficult to cut when using conventional tape dispensers. The cutting system of the DC 150 Sleeve allows the perfectly straight cut of Sleeve tape.

MADE IN FRANCE

DISPENSER FOR SLEEVE TYPE TAPES

STAINLESS STEEL BUILD

SUITABLE FOR USE IN CLEAN ENVIRONMENTS

PRESSURE TRIGGERED CUTTING SYSTEM

CAN BE MOUNTED ONTO A TABLE TOP

SUITABLE FOR INDUSTRIAL USE

USABLE AT A MAIN

Add to quote

In addition, this stainless-steel unit manufactured in France is extremely sturdy and is equipped with a Safe Cut system compatible with the standards for centres for persons with CAT and ESAT-type disabilities.

 

This manual dispenser is specifically adapted for use with Sleeve-type adhesive tapes. This material is usually used in very specific industries, particularly in the automotive and aeronautics industries. Sleeve is often used in the wrapping of network cables. Rolls of Sleeve tape usually have only one adhesive side so as to wrap the fabric around itself.

Ask for the data sheet
PRODUCT REFERENCE
REEL DIAMETER (mm)
MAX ROLL WIDTH (mm)
MAX DIAMETER OF ROLL (mm)
LENGTH
WIDTH
HEIGHT
DC 80 Sleeve
80 mm
250 mm
350 mm
320 mm
250 mm
220 mm
DC 150 Sleeve
150 mm
320 mm
350 mm
320 mm
270 mm
220 mm
DC 500 sleeve
jusqu'à 500 mm
670 mm
350 mm
320 mm
670 mm
220 mm

This manual dispenser is specifically adapted for use with Sleeve-type adhesive tapes. This material is usually used in very specific industries, particularly in the automotive and aeronautics industries. Sleeve is often used in the wrapping of network cables. Rolls of Sleeve tape usually have only one adhesive side so as to wrap the fabric around itself.

The DC 150 Sleeve sports an ingenious cutting system. In fact, Sleeve tape, and fabric in general, are extremely complicated components to cut on a regular basis. This manual dispenser is equipped with an adjustable pressure slider as well as an application roller, allowing the operator to keep the roll of Sleeve perfectly upright and without creases when dispensing and cutting. In addition, this slider allows the possibility of cutting in either direction, from left to right and from right to left.

 

This dispenser is also equipped with two metal tabs so as to stabilise the Sleeve tape at the time of dispensing and cutting.

 

This manual dispenser for Sleeve tape is equipped with a Solingen blade. Triangle-shaped and located on a swivel axis, this blade is extremely efficient and allows for smooth and easy cutting.

 

In addition, the entire cutting system is completely secure. User safety is of utmost importance to DERFI. This is why each of our devices in our secure industrial dispenser  range have a safety-reinforced cutting system. In the case of the DC 150 Sleeve, the cursor has been positioned so as to leave only a very small space between the latter and the cutting line. In this manner, it is impossible for the fingers or anything else to slip on the edge of the Solingen blade.

 

It is also important to note that the DC 150 Sleeve is made entirely from stainless steel and as such is an extremely sturdy manual dispenser. This dispenser is well suited for use in industrial environments. It is this stainless steel casing that ensures the longevity of this device all while requiring little to no maintenance.

The DC 150 Sleeve also has a very large reception capacity. It can accommodate rolls of up to 1400 mm wide, sporting an outside diameter of up to 180 mm. As for the hub mounting, the DC 150 Sleeve is compatible with the standard 76mm chuck size. Should other chuck sizes be required, DERFI can produce custom hubs.

 

DERFI also offers an additional hub system for the Sleeve tape manual cutting dispenser, so that the industrial operator can simultaneously handle two different types and sizes of adhesive on the same device.

Using this industrial dispenser for large adhesive rolls

The manual DC 150 Sleeve tape dispenser was specifically designed to assist in the cutting and handling of TESA Sleeve material. Once the roll has been installed and the Sleeve material is positioned on the cutting line, grasp the slider at the top handle and press downwards so as to lower the blade that will smooth the Sleeve surface with the rubber roller. Then slide the cutter through the tape while maintaining pressure. Once the piece of Sleeve is has been taken, this another piece of Sleeve can be cut simply by sliding the cutter in the opposite direction.

 

Setting up and loading the roll

First loosen the roller at the end of the right hub to adjust the opening. Then place the roll of Sleeve in the center of the hubs and bring down the circular plates in order to stabilize the adhesive roll. Finally secure the installation by tightening the wheel. Warning: note that the roll must be unwound from the top – therefore in a counterclockwise direction. Once the roll is correctly in place, take the end of the strip of Sleeve and guide it under the first training roll. Then, accompany it over the second roll and slide the adhesive tape under the two metal stabilizing flaps. Finally, bring the piece of Sleeve up to the cutting line. The manual Sleeve dispenser is now ready for its first cut.

 

Maintenance

This DC Sleeve type manual dispenser requires virtually no maintenance. Made entirely from rigid stainless steel, this sturdy industrial dispenser for woven tape will withstand the harsh environment and intensive use linked with industrial activity. From time to time, be sure to check for a potential buildup of glue residue on the Solingen blade. If this is the case, simply use a traditional detergent such as white spirits to clean the blade.

 

Spare parts

DERFI has all the spare parts for the DC 150 Sleeve manual dispenser available for speedy delivery upon request.

 

Spare parts

You want to do the maintenance yourself on this equipment ?
We recommend keeping these references in stock :

Lame Dc Sleeve

SM-12GWUU

You want to get more info about this product ?

Ask for the datasheet